welcome guest [ login ]
Welcome Guest!
Want to take part in these discussions? If you have an account, sign in now.
If you don't have an account, apply for one now.

Support: Mitsubishi Fuel Injectors

Bottom of Page

1 to 24 of 24

  1.  
    • CommentAuthorfireclown
    • CommentTimeDec 8th 2011
     
    Hi. I have a problem with entering a new injector code. The vehicle is a 2008 Mitsubishi L200. I have been using the 30 digit code of the top of the injector but it keeps telling me this is incorrect. It is still showing the old no in the ecu. Do i need to clear this and if sh how. Thanks Ian.
    • CommentAuthorAndrew
    • CommentTimeDec 12th 2011
     
    Hi Ian
    Sorry for delay. Which software version are you using?

    Andrew
    • CommentAuthorfireclown
    • CommentTimeDec 12th 2011
     
    Hi Andrew i have tried the latest and an earlier version. But still no luck. thanks Ian
    • CommentAuthordclyde
    • CommentTimeDec 15th 2011
     
    Hi entering new 30 digit code should overide old injector no need to clear. Let ecu completely time out approx 30 sec(until odometer disappears on meter) then try again. This can happen with OE tool.

    Regards

    Dom
    • CommentAuthorfireclown
    • CommentTimeDec 17th 2011
     
    Ok will try Mon. thanks.
    • CommentAuthorAndrew
    • CommentTimeJan 10th 2012 edited
     
    Hi, did you manage to do this?

    Dom, do you have a L200 & Shogun Inj code we can try with OE tool to check V30 operation?

    Andrew
    • CommentAuthordclyde
    • CommentTimeJan 11th 2012
     
    Hi Andrew i will get you injector code asap.

    Regards

    Dom
    • CommentAuthorfireclown
    • CommentTimeJan 17th 2012
     
    The customer has not been back to get it done, He should be in this week i will get the number for you. It is on top of the injector. But he does say it is running fine. no mil light either.
    • CommentAuthordclyde
    • CommentTimeJan 17th 2012
     
    Hi andrew injector codes 9100CF00CCCFD8E0E0000000000085, 91A3B3D9BFC8C3D1D00000000000ED, 91CBD300DBE2DEE8E6000000000060, 9100DA00CBD5CADDE00000000000A2. These are of a 2008 lwb V98W shogun. L200 use the same fuel system denso so you can use them for testing L200 function also. I tried both shogun & l200 with v30 but no use. Had to use o.e tool.

    Regards

    Dom
    • CommentAuthorAndrew
    • CommentTimeJan 18th 2012
     
    Thanks Dom

    Will get engineer to check V30 operation against OE tool

    Andrew
    • CommentAuthorfireclown
    • CommentTimeJan 19th 2012
     
    Hi no is 9000000000000000ef00000000007f hope this helps.
    • CommentAuthorAndrew
    • CommentTimeJan 23rd 2012
     
    Thanks!

    Andrew
    • CommentAuthorfireclown
    • CommentTimeJan 24th 2012
     
    Any news on this as he is suppose to be reappearing on Thurs. Thanks once again. Ian.
  14.  
    Hey, am new on the Autoboss forum just recently got the equipment. Would you enlighten me on the basics or what injector coding is?
    • CommentAuthortr6v30
    • CommentTimeJan 25th 2012
     
    Injector coding , sets the parameters for the injectors in the ECU.
    hope this helps
    • CommentAuthorAndrew
    • CommentTimeJan 27th 2012 edited
     
    Injector coding provides the vehicles ECU with the flow characteristics of each injector so it can balance the supplied/required fueling to balance the engine.

    Most systems are moving towards classified injectors whereby they are graded, IE 1, 2, 3 or 4.

    Replacement is simply a case of replacing like for like with no coding needed.

    Engineer is to check these coding operations next week when they return from the holiday.

    Andrew
    • CommentAuthorAndrew
    • CommentTimeFeb 1st 2012
     
    Engineer has checked and fixed the glitch, a new software version will be released very soon!

    Andrew
    • CommentAuthorfireclown
    • CommentTimeFeb 2nd 2012
     
    Thank you
    • CommentAuthorDimitris
    • CommentTime6 days ago
     
    hi i have the same problem. i can't entering a new injector code. i have the latest update in a mitsubishi 2007 - L200. i see that the letters of injector is capital letters and the letters will try to put in autoboss is small and can't change to capitals. i dodn't know if this is the reason of the problem but i can't entering new injectors.
    • CommentAuthorAndrew
    • CommentTime5 days ago edited
     
    HI, verified as working since V6.0?

    If you are having trouble can you log the procedure and send us the file please?




    V30 MITSUBISHI 6.0
    2012-3-2


    V6.0
    　 1.Add AutoLog Function.
    　 2.Correct the function of INJ.ID Writing(Exchanging INJ.)
    　 3.Correct the function of INJ.ID Writing(Exchanging ECU)
    　
    • CommentAuthorDimitris
    • CommentTime5 days ago
     
    I was trying to entering the injector before 3-4 days.
    i entering this "INJ.ID Writing(Exchanging INJ.) then

    No1. Injector ID Writing,
    No2. Injector ID Writing,
    No3. Injector ID Writing,
    No4. Injector ID Writing
    then i write the number of injector and nothing happens .
    i don't remember what message taking but the injector is not entering.
    i will have again the car in a week. with the new injector works fine but it is not good for the future.
    can help.?
    • CommentAuthorAndrew
    • CommentTime4 days ago
     
    Are you using software V6.0 or higher?

    Andrew
    • CommentAuthorDimitris
    • CommentTime3 days ago
     
    i use V6.1
    • CommentAuthorAndrew
    • CommentTime3 days ago
     
    HI, not sure why this would not work but can you create a log file if this fails please?

    regards

    Andrew

1 to 24 of 24

  1.